Receiver unit
M-GR10 series
User Manual

Compliant model: MGR10

Precautions

This manual describes the important precautions you should take for safe operation of this product.
Observe these precautions carefully to avoid personal injury, damage, fire, and other problems.

Meaning of symbols

WARNING

Failure to observe precautions carries the possibility of serious personal injury or death due to fire, electric shock, or other causes.

CAUTION

Failure to observe precautions may result in personal injury due to electric shock or other causes, and may damage other equipment.

Prohibited action

Mandatory action

Situation that needs attention

Notes and reference information

WARNING

If a foreign object (water, metal chips) enters this product, stop using immediately.
Continuing to use the product as it is may cause a fire or an electric shock.

If this product behaves abnormally, such as by generating heat or smoke, or giving off strange smells, cease usage immediately and shut down the connected device. After confirming that the product is not generating heat that will cause burns, remove this product from connected device. Afterwards, please contact your dealer.
Continuing to use the product as it is may cause a fire or an electric shock.

Please do not drop or hit this product.
In the event that this product is damaged, cease usage immediately and contact your dealer.

Fires or electric shocks may occur if this product is used when damaged.

Do not attempt to disassemble, modify, or repair this product.
Doing so may cause a fire, electric shock, or product damage.
Such malfunctions are not covered under warranty.

Do not put this product in fire.
Breakage may cause fire or injury.

Please do not insert or remove this product with wet hands. In addition, do not modify or forcibly bend the product.
It can cause a fire or electric shock.

This product presents a swallowing hazard for children, so be sure to store it in a place out of the reach of children.

CAUTION

Do not place this product in any of the following environments:

  • In a car exposed to sunlight or a place exposed to direct sunlight.
  • In a place that becomes hot, such as around a heater.
  • In a moist place or a place where condensation may occur.
  • In an uneven place or a place exposed to vibration.
  • In a place where a magnetic field is generated (such as near a magnet.)
  • In a dusty place.

This product does not have a waterproof structure. Use or store in a place not exposed to liquids such as water.
Any liquid such as rain, water spray, juice, coffee, steam, and sweat, can cause this product to breakdown.

  • Do not use this product with any device that may be significantly affected in the case of this product malfunctioning.
  • When you no longer need to use this product and the battery, be sure to dispose of them in accordance with the local ordinances and laws of your area.

Cautions for Wireless Equipment

This product is a wireless device that can use the entire 2.4 GHz band, and is able to avoid the mobile entity identification device range. The GFSK method is adopted as the radio wave method, and the interference distance is 10 m. The 2.4 GHz band is also used in medical devices, Bluetooth, and wireless LAN devices of the IEEE 802.11b/11g/11n standards.

  • Before using this product, check that there are no other “radio stations”* operating nearby.
  • If electromagnetic interference occurs between this product and other “radio stations”*, use this product in another location or stop using this product.

*Other “radio stations” refer to industrial, scientific and medical devices using the 2.4 GHz band, the same as this product, other radio stations of this type, licensed radio station premises for a mobile object identification system that is used in factory production lines, certain non-licensed low power radio stations, and amateur radio stations.

WARNING

  • Do not use with any equipment that may be significantly affected in the case of this product malfunctioning. There are rare cases in which an external radio wave at the same frequency, or the radio wave emitted from a mobile phone, causes this product to malfunction, slow down, or fail to operate.
  • Do not use this product in places where radio wave usage is prohibited, such as hospitals. Radio waves of this product may affect electronic devices and medical devices (for example pacemakers).
  • Due to the possibility of hindering safe navigation of aircraft, use of input devices in aircraft is prohibited by the Civil Aeronautics Act. Turn off the power of the input device before boarding and do not use after boarding.

*ELECOM is not liable for any accidents or any indirect or consequential damage incurred due to the failure of this product.

How to use

Items included in this package

The following items are included in this package. Verify the package to ensure all items are accounted for prior to using this product. While every effort has been made to ensure proper packaging, in the event that any shortage or damage is discovered, please contact the retailer where the product was purchased or ELECOM Product Support.

  • ELECOM Bridge G1000 USB receiver unit x 1

Name and function of each part

USB-A plug

Connects to the PC USB-A port.

Install ELECOM Mouse Assistant V6

ELECOM Mouse Assistant V6 must be installed to use to this product with supported devices.

■ Get ELECOM Mouse Assistant V6

Please visit our homepage below and download the latest version of the application.

Settings for the ELECOM Bridge G1000 USB Receiver

  • Settings for the ELECOM Bridge G1000 USB receiver are done on ELECOM Mouse Assistant V6. Download and install “ELECOM Mouse Assistant V6” from our company website. Refer to “Install ELECOM Mouse Assistant V6”.
  • To setup the connection using a mouse, please refer to the user manual for the mouse.

The following instructions are for the IST PRO.

1. Set the connection setting for the IST PRO to wireless connection ().

1) Connect your PC and the IST PRO using the included USB cable.

  • It does not matter which method (, , , , , ) is used to connect the IST PRO.
  • The operation mode can be in Mouse Assistant mode or hardware mode.

2) Start up ELECOM Mouse Assistant V6

3) Select the connected IST PRO on the home page.

The “Settings” page for the IST PRO will show up.

4) Select “Connection settings ” on the main page.

The “Connection settings” page for the IST PRO will show up.

5) On “Connection settings”, select wireless connection () on custom connections ( or ) to switch to wireless connection.

The connection settings for connection 1, connection 2, connection 3, and connection 4 cannot be changed for the IST PRO.

2. Pair this product with IST PRO wirelessly.

2) Plug this product into the USB-A port on the PC.

  • For devices that do not have a USB-A port, please use a USB Type-C® hub.

  • Ensure that the connector is correctly oriented to the port.
  • If there is strong resistance when inserting, check the shape and orientation of the connector. Forcibly inserting the connector may damage the connector, and there is a risk of injury.
  • Do not touch the terminal portion of the USB connector.

2) Start up ELECOM Mouse Assistant V6.

3) Select “Add device” on the main page.

4) Select “ELECOM Bridge G1000” under “Select connection type”.

5) Select the port to connect to under “Select pairing port”.

This product will enter pairing mode.

6) Turn on the IST PRO and turn the connection selection dial to or .

and must be set to wireless () under “Connection settings ()” on ELECOM Mouse Assistant V6.

7) Hold down the pairing button on the bottom of the IST PRO for around 3-4 seconds.

The IST PRO enters pairing mode, and the LED light on the side (orange) and the status light (white) on the bottom will blink slowly.

8) Pairing is complete when “Connection complete” appears.

When pairing is complete, the status light (white) on the bottom will turn off. The LED light on the side also lights up twice in orange.

Pairing between this product and the IST PRO is complete.

Specifications

Connector type

USB Type-A plug

Connection method

USB 2.4 GHz Wireless

Compatible models

USB port-equipped Windows OS, macOS, and ChromeOS devices

Supported OS

Windows 11/10, macOS Sonoma 14, ChromeOS
*ELECOM Mouse Assistant V6, the software required for paring this product with supported devices, is not available for ChromeOS. It is necessary to pair separately on a Windows PC and a Mac.

Power source

USB bus power

Dimensions

Approximately W16 × L19 × H9 mm / W0.63 × L0.75 × H0.36 in.

Weight

Approximately 2 g / 0.1 oz

Operating environment conditions

Temperature: 5 °C to 40 °C / 41 °F to 104 °F, humidity: 90 % RH (without condensation)

Storage environment conditions

Temperature: -10 °C to 60 °C / 14 °F to 140 °F, humidity: 90 % RH (without condensation)

What's Inside

ELECOM Bridge G1000 USB receiver unit x 1

Supported devices (Elecom products)

Devices supporting ELECOM Bridge G1000 USB receiver

Compliance status

Intellectual property rights

  • ELECOM CO., LTD. owns the copyright to this manual.
  • All products and company names on this product and the package are trademarks or registered trademarks of their respective owners.
  • Duplicating and transferring this document in part or whole is prohibited.
  • If you have any concerns or question regarding this manual, please contact the retailer from whom you purchased this product.
  • The specifications and appearance of this product may be changed without prior notice for product improvement purposes.
  • We shall bear no responsibility for any device failure or malfunction of other devices resulting from the use of this product.
  • When exporting this product, check the export regulations for the country of origin.
  • USB Type-C® and USB-C® are registered trademarks of USB Implementers Forum.

Support information